how much does it cost to replace a subaru key to Change a Subaru Spare Key

When you lose your Subaru car key, contact a locksmith. They can usually cut new keys for you at a lower cost than the dealer.

subaru key copy car keys are generally either smart "push-to-start" fob remote keys or simple keys made of metal. The Fob key will need to have its chip programmed.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your vehicle or the lift gate. These remotes use keys in your car to communicate with your vehicle's computer.

Subaru models come with a lesser well-known feature called PIN Code Access. It allows you to make a unique number sequence to start and open your vehicle. Read the owner's manual to learn how to use this feature if you own a Subaru Forester, Outback Crosstrek, WRX STI or Impreza.

It's possible that the battery in the key fob is dying. You can check the battery life of your key fob with an electronic tester that you can carry around or a multimeter that you have in your garage.

The next step is to take the circuit board of the transmitter from the key fob and examine it. This board will have one or two sets of 8-digit numbers, so jot down the first set so that you can remember it later. After you've done this, you can start programming the key fob at home. The procedure for doing this is different based on the model and year of your car but it's usually easy enough to do on your own.

Key Fobs

Subaru Legacy Key's most recent models all come with key fobs that not just open the doors, but also activate your lights, lock the gas cap, and even start your vehicle. This last feature is particularly helpful if you've found yourself at the gas station and your car won't even start because the battery inside the key fob has failed.

It is likely that your Subaru's key fob, regardless of whether it is old or new and can be replaced. It's important to note that newer models with the highest level of technological advancement may require an appointment at the dealership. With just a bit of effort and time, you can build your own replacement key fob.

Begin by looking at the circuit board that controls the transmitter on your key fob (instructions for opening the case should be provided in your owner's manual). It should have one or two sets of serial numbers each of which has 8 digits long. Note down the first number in the series and save it to refer to later.

Then, sit in your driver's seat, and close all doors. Turn the key 10 times to start your car, and then switch off the engine. Press the lock button on your key fob and then open the door to ensure that all doors work correctly. Then shut the door and take the key out of the ignition. The chime should be heard from your vehicle again and indicate that the key fob is programmed.

Ignition System

The key battery may be dead If your Subaru keys aren't functioning as they should. If you know how to get a new subaru key fob, you could replace the battery in your key fob yourself. A replacement battery is inexpensive and relatively easy to locate. If the key fob isn't responding to your commands it could be an issue with a different cause. It's recommended that you visit a dealer to get an extra key. They'll ensure that the key is genuine Subaru key that's in warranty. It will also be programmed to your vehicle. This is a lot easier and safer than buying an aftermarket key from a retailer online.

The dealer will also cut keys for you, provided you give them your VIN number as well as proof of ownership. They'll utilize this information to encode the replacement key in order to be accepted by the immobilizer. This is a more complicated process than simply cutting a key and the dealership will charge you more for it.

Once the new key is programmed, you can replace it into your working key. It will only take you five seconds to insert the new key, so make sure to keep your working keys close at fingertips. You can take the key off after the security light has stopped flashing and you can test it.

Battery Replacement

One of the most important features that makes subaru key fob fobs useful is their ability to turn on your car's power windows and sunroof by pressing of the button. However, the battery in your Subaru fob isn't intended to last forever, and will eventually need to be replaced. This short guide from Capitol Subaru will help you to change the battery yourself.

You'll first need to find the small gap that is the gap between the front and back of your keyfob. Using a small flathead screwdriver, you can pop this seam wide to reveal a small compartment that houses the battery. Install the new battery and make sure it's facing in the correct direction. Remove the old one. Once you have assembled everything, you can use the new key fob to lock the vehicle, unlocking it, and then starting your vehicle.

Always have a spare set of keys, particularly if the one you have is damaged or lost. You can purchase a new key from your local dealership or get it cut by a locksmith. Whatever you choose, it's essential to get your key fob functioning properly as soon as possible to allow you to drive safely!